How to Choose an Industrial Parts Washer: A Step-by-Step Buyer’s Guide
Last updated: November 3, 2026
To choose a parts washer for a production line, engineers work through a chain of decisions, from cleaning method to conveyor, heater and dryer. This guide takes them one step at a time, using the selection criteria Inline Cleaning Systems publishes, and ends with a quote worksheet.
Quick Answer: How Do You Choose a Parts Washer?
To choose a parts washer for a production line, start with the part and its contaminants, then set a cleanliness standard and pick a cleaning method. Next, match washer type, tunnel size, conveyor, heating, drying and filtration to your throughput and line speed. Finally, check utilities, wastewater, lead time and service support.
Key Observations
- Define contaminants and cleanliness first; every other choice follows.
- Aqueous spray suits light oils; ultrasonic suits fine particles and blind holes.
- Tunnel height should be at least 4 in (100 mm) above the tallest part.
- Gas heat suits tanks over 400 gallons or baths above 160 F.
- Most custom washers are delivered within 4 to 8 months of order.
- Sample parts allow cleaning trials before final design.
| Step | What you decide | Working rule |
|---|---|---|
| 1. Contaminants | Soils and cleanliness level | Five variables set the result |
| 2. Method | Spray, solvent or ultrasonic | Spray at 40 to 120 psi (3 to 8 bar) |
| 3. Washer type | Pass-through, batch or custom | Match part geometry and flow |
| 4. Size and conveyor | Tunnel, zones, belt, roller, or chain conveyor | 4 in (100 mm) height clearance |
| 5. Heat and filtration | Heaters, filters | Most baths 140 F to 160 F (60 C to 70 C) |
| 6. Drying | Blower type, heaters | High velocity ambient air for most parts, high volume heated air for tall parts |
| 7. Automation and utilities | Loading, safety, power, drain | Typically 480V or 575V three-phase |
Not sure which configuration fits? Inline Cleaning Systems reviews your part and process details and recommends one. Get a Free Quote or call +1 574-722-3714.
In this guide
- Quick answer
- Basics
- Contaminants
- Cleaning method
- Washer type
- Sizing and conveyors
- Heat and filtration
- Drying
- Automation
- Utilities
- Cost
- Quote worksheet
- Manufacturers
- FAQ
- Next step
What Is an Industrial Parts Washer and How Does It Work?
An industrial parts washer is a machine that automates the removal of oil, grease, dirt and metal chips from manufactured parts. Also called a parts washing machine or industrial parts cleaning machine, it typically takes parts through pre-cleaning, washing, rinsing and drying stages.
Aqueous cleaning means washing with hot water and water-based detergent instead of solvent. Pumps push the solution through a bag filter and spray nozzles, and it drains back to be filtered and reused. This closed-loop wash system minimizes water and detergent use and extends bath life.
A pass-through washer carries parts on a continuous conveyor through each stage without manual handling in between.
Who this applies to: engineers at OEM and Tier 1 plants specifying pass-through, rotary batch or custom automated washers, not bench or cabinet units.
Step 1: What Contaminants and Cleanliness Level Must You Meet?
Choosing an industrial part washer starts with what must come off the part and how clean it must be. Inline Cleaning Systems starts every design from the part, its contamination, the cleanliness requirement, the line speed and the upstream and downstream processes.
List each soil and what the next process needs. The Inline parts washer FAQ names five variables that decide the result:
- Time: the minimum detergent contact time.
- Temperature: most commonly 140 F to 160 F.
- Chemistry: the correct detergent and concentration.
- Pressure: typically 40 to 120 psi for spray washers.
- Filtration: contamination left in the solution can end up on parts.
Step 2: Which Cleaning Method Fits: Aqueous, Solvent or Ultrasonic?
The cleaning method follows from the soil. Aqueous spray handles light oils and debris, high-temperature aqueous or solvent cleaning suits heavy oils, and ultrasonic cleaning reaches fine particles and blind holes. Inline Cleaning Systems specializes in high-volume aqueous spray washers, which clean parts with pressurized detergent.
Aqueous vs Solvent Parts Washer: Which Is Better?
For most applications, an aqueous parts washer is the better choice. Water-based cleaning solution is generally less flammable, gives off fewer hazardous fumes and lower VOC levels, is often biodegradable and is easier for operators to handle. Solvent systems still suit some specialty uses.
Step 3: Which Type of Parts Washer Do You Need?
The best parts washer is the type that matches your part geometry and production flow. Inline Cleaning Systems builds single, two and three stage pass-through conveyor parts washers, rotary and carousel batch washers, and custom washer products for cylinders, long bores, gears and seed boxes.
- Single-stage: wash or rinse only, for parts that can flash dry.
- Two-stage: wash and rinse, or wash and dry.
- Three-stage: wash, rinse and dry, plus an optional halo rinse, a mist of deionized (DI) or reverse osmosis (RO) water for spot-free parts.
- Rotary or carousel batch: complex parts which should be loaded and unloaded at the same position.
- Custom: parts that need fixtures, bore probes or 360-degree spray and drying.
Conveyor vs Batch Parts Washer: Which Fits Your Part?
A pass-through conveyor washer fits continuous, high-volume flow because parts move through every stage without handling in between. A rotary or carousel batch washer fits hydraulic and complex parts that need fixtures and bore probes, and returns them to one operator in a compact footprint. This decision table maps common parts to the washer Inline typically uses.
| Part type | Washer that fits | Design detail |
|---|---|---|
| Stamped parts off a press | Pass-through at the press exit | High line speeds; casters to move between presses |
| Machined or ground parts | Pass-through before finishing or assembly | Conveyor, robot or pick-and-place loading |
| Ground cylinders or round tubes, full outside diameter | Slanted roller conveyor washer | Tilt aligns parts so nozzles reach the bores |
| Long tubes and extrusions | Pass-through with powered rollers | Spray and air reach the underside, but not the inside |
| Long bores, such as hydraulic cylinders | Tube washer | A probe washes and dries the full bore |
| Hydraulic parts and gears | Rotary batch washer or gear washer | Probes clean internal bores, spray from all sides |
| Small parts needing fixed orientation | Fixtured indexing washer, such as the valve plunger washer | Pick-and-place loads individual fixtures |
| Seed boxes and dunnage | Seed tote washer | 360-degree rotation; heated wash option |
| Strip or sheet | Wet brush line | Wash, brush, rinse, treat, dry |
Step 4: How Do You Size a Conveyor Parts Washer?
A conveyor parts washer is sized by tunnel width, tunnel height and zone length. Tunnel height should be at least 4 inches (100 mm) above the tallest part. Common widths are 4, 8, 12, 16, 24, 30 and 36 in, and Inline Cleaning Systems can build any width the parts require up to 100 inches.
Size a large industrial parts washer the same way:
- Set tunnel width and height from the largest part.
- Size zone length from detergent contact time and line speed.
- Size the dry zone from the air passes needed at the target speed.
Unistrut mounts let zone dividers and air knife brackets move if the process changes (see washer features).
Which Conveyor Should a Parts Washer Use?
The standard conveyor on Inline pass-through washers is a stainless steel mesh belt, typically 1 in by 1 in. Plastic mesh protects parts that must not be marked, powered rollers carry tubes and panels, and chain conveyors with fixtures hold parts in a fixed orientation.
| Conveyor | Best for | Trade-off |
|---|---|---|
| Stainless flat wire belt | Maximum open area for cleaning and drying | Durable, economical, highest open area |
| Plastic mesh belt | Parts that must not mar | Costs more; less open area |
| Powered rollers | Tubes, panels, extrusions | Open spacing cleans and dries undersides |
| Chain with fixtures | Orientation, indexing, support | Indexes during loading and unloading |
Step 5: How Should the Washer Heat and Filter the Wash Solution?
Heating and filtration keep the wash bath working. Pick heat by tank size, temperature and plant utilities, and filtration by the contaminants and cleanliness requirement from Step 1.
Electric, Gas or Steam: Which Heating Should You Choose?
Electric immersion heaters are standard on Inline Cleaning Systems washers and suit small and medium machines, delivering heat directly to the bath with minimal losses. Gas burners are recommended for tanks over 400 gallons, temperatures above 160 F, or lower electric use. Steam heat uses excess plant steam through a shell and tube heat exchanger.
How Do Filtration and Oil Skimming Protect the Bath?
Filtration and oil control matter because any contamination in the solution can end up on the parts. Oil skimming means lifting floating oil off the solution so it cannot redeposit on parts or shorten bath life. Inline Cleaning Systems washers can include a removable chip basket, bag filters and a belt-type oil skimmer.
- Chip basket: catches large debris, protecting the pump.
- Bag filters: typically 100 or 200 micron, down to 10 micron or less.
- Magnet: traps small ferrous particles ahead of the second-stage filter.
- Belt skimmer: works best off shift, when the solution is still.
- Coalescing filter: for heavy oil or 24-hour operation.
Step 6: How Should the Washer Dry the Parts?
Drying is often the hardest stage to design for complex geometries, blind holes and high line speeds. Drying the parts sufficiently without wasting energy requires a careful analysis of the part geometry and process requirements. The type of blower, temperature, and nozzle placement should be defined by part geometry and line speed.
How Are Parts Dried After Washing?
Inline chooses one of three dry configurations based on your parts and process requirements:
- High velocity ambient air: This is the most common since it works on a large variety of parts and uses the least amount of energy. Water is blown off the part using high velocity air (typically 30,000+ ft/min, or 165 m/s) from air knives or nozzles.
- High velocity heated air: Heat is added for very thin parts which do not hold enough heat to flash dry quickly after exiting the dry stage. Inline electric heaters raise the air temperature up to a programmed temperature, and the air is not recirculated.
- Recirculated high volume (lower velocity) heated air: This method removes moisture by blow off as well as evaporation, and is commonly used on tall parts which are far from air knives or nozzles. Air is recirculated through the blower and uses an electric heater to raise the air to a set temperature.
Step 7: What Automation and Safety Features Should You Specify?
Automation sets how parts enter and leave the washer and how operators stay safe. Inline Cleaning Systems designs complete systems, including material handling, with load sensors, pick-and-place units and robot integration, Category 3 safety and PLC controls with a touchscreen HMI.
- Category 3 safety: a dedicated safety controller, dual monitored contacts and safe torque off on drives.
- Guarding: light curtains or custom guarding.
- Controls: smart relay with push buttons, or PLC-based with a color touchscreen HMI; Allen Bradley is standard on pass-through washers, with Siemens and other brands available.
- Chemistry: automatic water fill, dosing, and conductivity and pH monitoring.
Planning a washer for a press line or robot cell? Send your part and line details for a recommended configuration. Get a Free Quote or call +1 574-722-3714.
Step 8: What Utilities and Wastewater Planning Does a Parts Washer Need?
A production parts washer needs electrical power, water, a drain and exhaust ventilation, and most Inline Cleaning Systems washers do not need compressed air. In North America, power is typically 480V or 575V three-phase, with amperage scaled to heater and motor loads. Inline confirms exact needs on the installation drawings.
- Power: 480V or 575V three-phase; other voltages for international sites.
- Water: initial fill and top-off; RO or DI water for a spot-free rinse.
- Drain: floor drain or holding tank for periodic bath dumps.
- Exhaust: a fan to a customer-supplied stack, or a mist collector if there is no ductwork.
How Is Parts Washer Wastewater Handled?
Parts washer wastewater comes from periodic dumps of used solution, and disposal depends on local regulations and bath contamination. Many aqueous detergents are drain-safe for sanitary sewer where codes permit. Heavy oil usually needs skimming, coalescing or filtration before discharge.
Where on-site discharge is not allowed, a licensed waste handler collects the solution. Inline can recommend oil-water separation equipment to reduce disposal volumes.
How Much Does an Industrial Parts Washer Cost?
Industrial parts washer cost depends on size, number of stages, throughput, materials and options such as mist collectors, exhaust fans, filtration and automation. Inline Cleaning Systems engineers every washer to order and provides a tailored quote from your part and process details.
- Size: tunnel dimensions and number of zones.
- Stages: single-stage up to lines such as the 7-stage washer.
- Throughput: faster lines need longer zones.
Operating cost depends on water, detergent and energy use. Inline lowers it with closed-loop recirculation, direct immersion heat, cascaded rinse water, insulated tanks and efficient pumps, and can adapt a proven standard design for a lower-cost build.
What Should You Send a Manufacturer for a Parts Washer Quote?
Send the details that size and configure the machine: part dimensions, weight, material and geometry; the contaminants; the cleanliness requirement; target throughput; available floor space; and the upstream and downstream processes. Inline Cleaning Systems also welcomes sample parts, which often let its team validate the approach through cleaning trials before final design.
Copy this worksheet into your request:
| Quote item | What to provide | What it decides |
|---|---|---|
| Part dimensions | Largest length, width, height | Tunnel size and clearance |
| Weight and material | Heaviest part, base material | Part support, detergent chemistry |
| Geometry | Bores, blind holes, threads | Spray probes and drying design |
| Contaminants | Oils, grease, chips, fines | Method, filtration, oil control |
| Cleanliness requirement | What the next process needs | Stages, halo rinse, filter rating |
| Throughput and line speed | Target rate | Zone and dry-zone length |
| Available footprint | Floor space and layout | Pass-through or compact batch |
| Upstream and downstream | Press, machining, finishing, assembly | Placement, loading, integration |
| Sample parts | Representative production parts | Cleaning trials |
Can You Test Parts Before Buying a Washer?
Yes. Inline Cleaning Systems welcomes sample parts and often helps validate the approach through cleaning trials before final design. Inline can also run cleaning trials at its facility to validate the detergent chemistry for your contaminants, substrate materials and water quality before commissioning.
How Long Does It Take to Get a Custom Parts Washer?
Most custom parts washers from Inline Cleaning Systems are delivered within 4 to 8 months of order, with a project-specific schedule given during quoting. Each washer is engineered to order, built in-house and factory acceptance tested before it ships, so plan facility work around that window.
How Do You Evaluate Parts Washer Manufacturers?
Judge parts washer manufacturers on who designs, builds, installs and services the machine, and whether they can support it years later. Inline Cleaning Systems has built engineered parts washers since 1980, with machining, fabrication, welding, assembly, paint and controls done in-house in Lafayette, Indiana.
Ask each manufacturer about:
- Contacts: Inline sales staff are engineers and a single point of contact.
- Testing: factory acceptance testing before shipment.
- One team: the builders also install, commission, train operators and service the machine.
- Capacity: over 44,000 sq ft of space in Lafayette, Indiana and Victor, New York.
Read more about Inline Cleaning Systems and its in-house machining and fabrication services.
FAQ: Choosing an Industrial Parts Washer
The best chemical is the detergent matched to your contaminants, substrate materials and water quality. Inline Cleaning Systems helps identify that chemistry. You can buy detergent from a chemical supplier, and Inline can recommend trusted partners or run cleaning trials to validate it.
Whether a parts washer is worth it depends on your volumes and the cleanliness the next process needs. On a production line, a conveyorized washer moves parts through wash, rinse and dry stages without manual handling, and a closed loop minimizes water and detergent use.
Most industrial parts washers run at 140 F to 160 F (60 C to 70 C). Lower temperatures can cause excess foam, while higher ones use more energy and make more steam but can dissolve tougher oils. The ideal setpoint depends on detergent and contamination.
In many cases, yes. Inline Cleaning Systems engineering assesses the existing machine and recommends the most cost-effective path, whether that is an upgrade or a replacement. Share the current machine’s details and your new cleaning requirement to start the assessment.
Yes, for Inline washers. Inline Cleaning Systems keeps the original drawings and specifications for every washer it has shipped, and its in-house machine shop and purchasing team supply exact replacement parts. That record lets Inline support older machines across an installed base that spans decades.
Every Inline Cleaning Systems washer carries a manufacturer warranty covering parts and workmanship, with specific terms confirmed in the quotation. The same team that builds the washer stays with it afterward, so customers are not handed off to an unfamiliar contractor. That team handles installation and commissioning, operator training and future service visits.
Next Step: Get a Washer Configuration for Your Parts
The most direct way to choose a parts washer is to put real parts and process data in front of the engineers who will build it. Send Inline Cleaning Systems the worksheet details and sample parts, and the team will recommend a configuration.
Get a Free Quote, call +1 574-722-3714, contact the engineering team, or browse the full product range of industrial cleaning systems.
Related reading: aqueous parts washers | automated parts washers | industrial parts cleaning | parts washer maintenance