How to Choose an Industrial Parts Washer: A Step-by-Step Buyer’s Guide

Last updated: November 3, 2026

To choose a parts washer for a production line, engineers work through a chain of decisions, from cleaning method to conveyor, heater and dryer. This guide takes them one step at a time, using the selection criteria Inline Cleaning Systems publishes, and ends with a quote worksheet.

Quick Answer: How Do You Choose a Parts Washer?

To choose a parts washer for a production line, start with the part and its contaminants, then set a cleanliness standard and pick a cleaning method. Next, match washer type, tunnel size, conveyor, heating, drying and filtration to your throughput and line speed. Finally, check utilities, wastewater, lead time and service support.

Key Observations

StepWhat you decideWorking rule
1. ContaminantsSoils and cleanliness levelFive variables set the result
2. MethodSpray, solvent or ultrasonicSpray at 40 to 120 psi (3 to 8 bar)
3. Washer typePass-through, batch or customMatch part geometry and flow
4. Size and conveyorTunnel, zones, belt, roller, or chain conveyor4 in (100 mm) height clearance
5. Heat and filtrationHeaters, filtersMost baths 140 F to 160 F (60 C to 70 C)
6. DryingBlower type, heatersHigh velocity ambient air for most parts, high volume heated air for tall parts
7. Automation and utilitiesLoading, safety, power, drainTypically 480V or 575V three-phase

Not sure which configuration fits? Inline Cleaning Systems reviews your part and process details and recommends one. Get a Free Quote or call +1 574-722-3714.

In this guide

  1. Quick answer
  2. Basics
  3. Contaminants
  4. Cleaning method
  5. Washer type
  6. Sizing and conveyors
  7. Heat and filtration
  8. Drying
  9. Automation
  10. Utilities
  11. Cost
  12. Quote worksheet
  13. Manufacturers
  14. FAQ
  15. Next step

What Is an Industrial Parts Washer and How Does It Work?

An industrial parts washer is a machine that automates the removal of oil, grease, dirt and metal chips from manufactured parts. Also called a parts washing machine or industrial parts cleaning machine, it typically takes parts through pre-cleaning, washing, rinsing and drying stages.

Aqueous cleaning means washing with hot water and water-based detergent instead of solvent. Pumps push the solution through a bag filter and spray nozzles, and it drains back to be filtered and reused. This closed-loop wash system minimizes water and detergent use and extends bath life.

A pass-through washer carries parts on a continuous conveyor through each stage without manual handling in between.

Who this applies to: engineers at OEM and Tier 1 plants specifying pass-through, rotary batch or custom automated washers, not bench or cabinet units.

Step 1: What Contaminants and Cleanliness Level Must You Meet?

Choosing an industrial part washer starts with what must come off the part and how clean it must be. Inline Cleaning Systems starts every design from the part, its contamination, the cleanliness requirement, the line speed and the upstream and downstream processes.

List each soil and what the next process needs. The Inline parts washer FAQ names five variables that decide the result:

Step 2: Which Cleaning Method Fits: Aqueous, Solvent or Ultrasonic?

The cleaning method follows from the soil. Aqueous spray handles light oils and debris, high-temperature aqueous or solvent cleaning suits heavy oils, and ultrasonic cleaning reaches fine particles and blind holes. Inline Cleaning Systems specializes in high-volume aqueous spray washers, which clean parts with pressurized detergent.

Aqueous vs Solvent Parts Washer: Which Is Better?

For most applications, an aqueous parts washer is the better choice. Water-based cleaning solution is generally less flammable, gives off fewer hazardous fumes and lower VOC levels, is often biodegradable and is easier for operators to handle. Solvent systems still suit some specialty uses.

Step 3: Which Type of Parts Washer Do You Need?

The best parts washer is the type that matches your part geometry and production flow. Inline Cleaning Systems builds single, two and three stage pass-through conveyor parts washers, rotary and carousel batch washers, and custom washer products for cylinders, long bores, gears and seed boxes.

Conveyor vs Batch Parts Washer: Which Fits Your Part?

A pass-through conveyor washer fits continuous, high-volume flow because parts move through every stage without handling in between. A rotary or carousel batch washer fits hydraulic and complex parts that need fixtures and bore probes, and returns them to one operator in a compact footprint. This decision table maps common parts to the washer Inline typically uses.

Part typeWasher that fitsDesign detail
Stamped parts off a pressPass-through at the press exitHigh line speeds; casters to move between presses
Machined or ground partsPass-through before finishing or assemblyConveyor, robot or pick-and-place loading
Ground cylinders or round tubes, full outside diameterSlanted roller conveyor washerTilt aligns parts so nozzles reach the bores
Long tubes and extrusionsPass-through with powered rollersSpray and air reach the underside, but not the inside
Long bores, such as hydraulic cylindersTube washerA probe washes and dries the full bore
Hydraulic parts and gearsRotary batch washer or gear washerProbes clean internal bores, spray from all sides
Small parts needing fixed orientationFixtured indexing washer, such as the valve plunger washerPick-and-place loads individual fixtures
Seed boxes and dunnageSeed tote washer360-degree rotation; heated wash option
Strip or sheetWet brush lineWash, brush, rinse, treat, dry

Step 4: How Do You Size a Conveyor Parts Washer?

A conveyor parts washer is sized by tunnel width, tunnel height and zone length. Tunnel height should be at least 4 inches (100 mm) above the tallest part. Common widths are 4, 8, 12, 16, 24, 30 and 36 in, and Inline Cleaning Systems can build any width the parts require up to 100 inches.

Size a large industrial parts washer the same way:

Unistrut mounts let zone dividers and air knife brackets move if the process changes (see washer features).

Which Conveyor Should a Parts Washer Use?

The standard conveyor on Inline pass-through washers is a stainless steel mesh belt, typically 1 in by 1 in. Plastic mesh protects parts that must not be marked, powered rollers carry tubes and panels, and chain conveyors with fixtures hold parts in a fixed orientation.

ConveyorBest forTrade-off
Stainless flat wire beltMaximum open area for cleaning and dryingDurable, economical, highest open area
Plastic mesh beltParts that must not marCosts more; less open area
Powered rollersTubes, panels, extrusionsOpen spacing cleans and dries undersides
Chain with fixturesOrientation, indexing, supportIndexes during loading and unloading

Step 5: How Should the Washer Heat and Filter the Wash Solution?

Heating and filtration keep the wash bath working. Pick heat by tank size, temperature and plant utilities, and filtration by the contaminants and cleanliness requirement from Step 1.

Electric, Gas or Steam: Which Heating Should You Choose?

Electric immersion heaters are standard on Inline Cleaning Systems washers and suit small and medium machines, delivering heat directly to the bath with minimal losses. Gas burners are recommended for tanks over 400 gallons, temperatures above 160 F, or lower electric use. Steam heat uses excess plant steam through a shell and tube heat exchanger.

How Do Filtration and Oil Skimming Protect the Bath?

Filtration and oil control matter because any contamination in the solution can end up on the parts. Oil skimming means lifting floating oil off the solution so it cannot redeposit on parts or shorten bath life. Inline Cleaning Systems washers can include a removable chip basket, bag filters and a belt-type oil skimmer.

Step 6: How Should the Washer Dry the Parts?

Drying is often the hardest stage to design for complex geometries, blind holes and high line speeds. Drying the parts sufficiently without wasting energy requires a careful analysis of the part geometry and process requirements. The type of blower, temperature, and nozzle placement should be defined by part geometry and line speed.

How Are Parts Dried After Washing?

Inline chooses one of three dry configurations based on your parts and process requirements:

Step 7: What Automation and Safety Features Should You Specify?

Automation sets how parts enter and leave the washer and how operators stay safe. Inline Cleaning Systems designs complete systems, including material handling, with load sensors, pick-and-place units and robot integration, Category 3 safety and PLC controls with a touchscreen HMI.

Planning a washer for a press line or robot cell? Send your part and line details for a recommended configuration. Get a Free Quote or call +1 574-722-3714.

Step 8: What Utilities and Wastewater Planning Does a Parts Washer Need?

A production parts washer needs electrical power, water, a drain and exhaust ventilation, and most Inline Cleaning Systems washers do not need compressed air. In North America, power is typically 480V or 575V three-phase, with amperage scaled to heater and motor loads. Inline confirms exact needs on the installation drawings.

How Is Parts Washer Wastewater Handled?

Parts washer wastewater comes from periodic dumps of used solution, and disposal depends on local regulations and bath contamination. Many aqueous detergents are drain-safe for sanitary sewer where codes permit. Heavy oil usually needs skimming, coalescing or filtration before discharge.

Where on-site discharge is not allowed, a licensed waste handler collects the solution. Inline can recommend oil-water separation equipment to reduce disposal volumes.

How Much Does an Industrial Parts Washer Cost?

Industrial parts washer cost depends on size, number of stages, throughput, materials and options such as mist collectors, exhaust fans, filtration and automation. Inline Cleaning Systems engineers every washer to order and provides a tailored quote from your part and process details.

Operating cost depends on water, detergent and energy use. Inline lowers it with closed-loop recirculation, direct immersion heat, cascaded rinse water, insulated tanks and efficient pumps, and can adapt a proven standard design for a lower-cost build.

What Should You Send a Manufacturer for a Parts Washer Quote?

Send the details that size and configure the machine: part dimensions, weight, material and geometry; the contaminants; the cleanliness requirement; target throughput; available floor space; and the upstream and downstream processes. Inline Cleaning Systems also welcomes sample parts, which often let its team validate the approach through cleaning trials before final design.

Copy this worksheet into your request:

Quote itemWhat to provideWhat it decides
Part dimensionsLargest length, width, heightTunnel size and clearance
Weight and materialHeaviest part, base materialPart support, detergent chemistry
GeometryBores, blind holes, threadsSpray probes and drying design
ContaminantsOils, grease, chips, finesMethod, filtration, oil control
Cleanliness requirementWhat the next process needsStages, halo rinse, filter rating
Throughput and line speedTarget rateZone and dry-zone length
Available footprintFloor space and layoutPass-through or compact batch
Upstream and downstreamPress, machining, finishing, assemblyPlacement, loading, integration
Sample partsRepresentative production partsCleaning trials

Can You Test Parts Before Buying a Washer?

Yes. Inline Cleaning Systems welcomes sample parts and often helps validate the approach through cleaning trials before final design. Inline can also run cleaning trials at its facility to validate the detergent chemistry for your contaminants, substrate materials and water quality before commissioning.

How Long Does It Take to Get a Custom Parts Washer?

Most custom parts washers from Inline Cleaning Systems are delivered within 4 to 8 months of order, with a project-specific schedule given during quoting. Each washer is engineered to order, built in-house and factory acceptance tested before it ships, so plan facility work around that window.

How Do You Evaluate Parts Washer Manufacturers?

Judge parts washer manufacturers on who designs, builds, installs and services the machine, and whether they can support it years later. Inline Cleaning Systems has built engineered parts washers since 1980, with machining, fabrication, welding, assembly, paint and controls done in-house in Lafayette, Indiana.

Ask each manufacturer about:

Read more about Inline Cleaning Systems and its in-house machining and fabrication services.

FAQ: Choosing an Industrial Parts Washer

What is the best chemical to use in a parts washer?

The best chemical is the detergent matched to your contaminants, substrate materials and water quality. Inline Cleaning Systems helps identify that chemistry. You can buy detergent from a chemical supplier, and Inline can recommend trusted partners or run cleaning trials to validate it.

Are parts washers worth it for a production line?

Whether a parts washer is worth it depends on your volumes and the cleanliness the next process needs. On a production line, a conveyorized washer moves parts through wash, rinse and dry stages without manual handling, and a closed loop minimizes water and detergent use.

What temperature should an industrial parts washer run at?

Most industrial parts washers run at 140 F to 160 F (60 C to 70 C). Lower temperatures can cause excess foam, while higher ones use more energy and make more steam but can dissolve tougher oils. The ideal setpoint depends on detergent and contamination.

Can an existing parts washer be retrofitted or upgraded?

In many cases, yes. Inline Cleaning Systems engineering assesses the existing machine and recommends the most cost-effective path, whether that is an upgrade or a replacement. Share the current machine’s details and your new cleaning requirement to start the assessment.

Can you get spare parts for an older parts washer?

Yes, for Inline washers. Inline Cleaning Systems keeps the original drawings and specifications for every washer it has shipped, and its in-house machine shop and purchasing team supply exact replacement parts. That record lets Inline support older machines across an installed base that spans decades.

What warranty comes with an industrial parts washer?

Every Inline Cleaning Systems washer carries a manufacturer warranty covering parts and workmanship, with specific terms confirmed in the quotation. The same team that builds the washer stays with it afterward, so customers are not handed off to an unfamiliar contractor. That team handles installation and commissioning, operator training and future service visits.

Next Step: Get a Washer Configuration for Your Parts

The most direct way to choose a parts washer is to put real parts and process data in front of the engineers who will build it. Send Inline Cleaning Systems the worksheet details and sample parts, and the team will recommend a configuration.

Get a Free Quote, call +1 574-722-3714, contact the engineering team, or browse the full product range of industrial cleaning systems.

Related reading: aqueous parts washers | automated parts washers | industrial parts cleaning | parts washer maintenance